تعتبر شركة Olux شركة رائدة ومتميزة على المستوى الدولي في مجال البحث والتطوير وتصنيع وبيع محطات التكسير والغربلة واسعة النطاق ومعدات الطحن الصناعية ومصانع الاستفادة.
The vibration motor is equipped with heavier eccentric blocks at both ends. If it is installed vertically or obliquely, the bearing axial direction must bear the gravity of the eccentric block. If there is no special device (ie, Plane bearing) in the vibration motor, it will have a bad influence on the bearing, thus shortening the service life.
WhatsApp: +86 18221755073
Due to the unreasonable design of the lubrication seal structure, the bearing lubrication is not sufficient, which is the main reason for the deformation and burnout of the bearing due to heat. Solution: Use thin oil lubrication, improve the lubrication channel, improve the sealing structure.
WhatsApp: +86 18221755073
Due to the the poor working condition, the bearing of circular vibrating screen not only bears a great impact load under the adjustment state, but also completes the circular motion when it rotates around its central axis with bearing a high radial acceleration and centrifugal force.
WhatsApp: +86 18221755073
Common faults of vibrating screens are as follows: failure to start, or small amplitude, abnormal material movement, poor screening quality, and bearing heating. For these common faults, a brief summary of several solutions for …
WhatsApp: +86 18221755073
The vibration motor is equipped with heavier eccentric blocks at both ends. If it is installed vertically or obliquely, the bearing axial direction must bear the gravity of the eccentric …
WhatsApp: +86 18221755073
Due to the unreasonable design of the lubrication seal structure, the bearing lubrication is not sufficient, which is the main reason for the deformation and burnout of the bearing due to heat. Solution: Use thin oil …
WhatsApp: +86 18221755073
Because the bearing on the vibrating screen bears a large load, a high frequency, and the load is always changing, the bearing must adopt a large clearance. If the bearing with ordinary clearance is used, the outer ring of the bearing must be grinded again to make it a large clearance.
WhatsApp: +86 18221755073
During operation, the inner cavity bearing of the vibration exciter often appears high temperature, burned or even locked, which causes the vibration exciter to not work normally, which directly affects the production of the crushing station.
WhatsApp: +86 18221755073
When the mud content and water content in the feed are high, the material will stick to the sieve hole and block the sieve hole. At this time, the sieve hole should be cleaned first, and then the spray amount and the inclination angle of the sieve surface should be adjusted appropriately.
WhatsApp: +86 18221755073
Worn Bearings: Bearings can wear out, leading to excessive vibrations. Solutions: Check and Balance the Screen: Ensure that the load is evenly distributed across the screen. Regularly inspect and balance the …
WhatsApp: +86 18221755073
Due to the lubrication sealing structure design is unreasonable, inadequate bearing lubrication, is lead to deformation of the bearing heats, and the main reason for the loss. Solution: use thin oil lubrication, improve lubrication channels, improve the sealing structure.
WhatsApp: +86 18221755073
Here are five reasons why bearing temperature is too high in most industrial applications : 1: Quality problems. Bad quality bearing of vibrating screen will lead to serious wear and tear of the bearing when the vibrating screen is …
WhatsApp: +86 18221755073
The vibrating screen cannot be started or the amplitude is too small. It should be checked whether there is any obstacle in the electrical, whether the vibration motor is damaged, or the components in the line are damaged, and the voltage is insufficient.
WhatsApp: +86 18221755073
Worn Bearings: Bearings can wear out, leading to excessive vibrations. Solutions: Check and Balance the Screen: Ensure that the load is evenly distributed across the screen. Regularly inspect and balance the vibrating motor. Tighten Bolts: Inspect and tighten all bolts and fasteners regularly.
WhatsApp: +86 18221755073
Due to the lubrication sealing structure design is unreasonable, inadequate bearing lubrication, is lead to deformation of the bearing heats, and the main reason for the loss. Solution: use thin …
WhatsApp: +86 18221755073
Here are five reasons why bearing temperature is too high in most industrial applications : 1: Quality problems. Bad quality bearing of vibrating screen will lead to serious wear and tear of the bearing when the vibrating …
WhatsApp: +86 18221755073
Due to the the poor working condition, the bearing of circular vibrating screen not only bears a great impact load under the adjustment state, but also completes the circular motion when it rotates around its central axis with bearing a high radial …
WhatsApp: +86 18221755073
Common faults of vibrating screens are as follows: failure to start, or small amplitude, abnormal material movement, poor screening quality, and bearing heating. For these common faults, a brief summary of several solutions for your reference.
WhatsApp: +86 18221755073